Mold Remediation Service Universal City
Dry Ice Blasting Mold

Dry Ice Blasting Mold in UNIVERSAL CITY, California

Dry Ice Blasting Mold in UNIVERSAL CITY, California is a dry, chemical-free way to strip mold off wood framing, sheathing, and structural cavities without soaking your home. We use it for attic growth, crawl space contamination, and post-leak cleanup where wet methods would damage the substrate. If you have musty odors or visible black mold, we can inspect and blast the same week.

Service overview

Dry Ice Blasting Mold in UNIVERSAL CITY, California

Dry ice blasting mold in UNIVERSAL CITY, California uses compressed pellets of solid carbon dioxide at roughly -109°F to freeze and lift mold, spores, and surface debris off wood, brick, and metal. The pellets sublimate on contact, so there is no grit, no water, and no secondary media to clean up. It is the same technology used to strip industrial equipment, adapted here for structural mold removal in attics, crawl spaces, and wall cavities where moisture is the enemy. Universal City sits in a warm, dry basin, but the hillside homes around Universal City Plaza and the older multifamily buildings near the studios still trap moisture in attics and crawl spaces. A slow roof leak, a failed supply line, or a bathroom exhaust vented into the attic can seed black mold growth behind drywall within 48 to 72 hours. When you need dry ice mold remediation in UNIVERSAL CITY, we inspect first, contain the work zone, then blast the affected framing clean.

! Common warning signs

Musty odors after a cleaning that will not go away

Lingering musty odors usually mean mold is growing inside a wall cavity, attic, or HVAC system where you cannot see it. Wiping surfaces does nothing because the colony is behind the drywall.

Black mold growth behind drywall after a pipe leak

A slow supply line leak can seed black mold growth behind drywall in 48 to 72 hours. By the time you see a stain, the colony has usually spread along the studs and into the insulation.

Crawl space mold after heavy rain

Crawl space mold after rain spreads fast when soil stays wet and ventilation is poor. The growth climbs the joists and subfloor, and the musty air migrates up into the living space.

Scope of work

What our dry ice blasting mold service includes

Every dry ice blasting mold job in Universal City includes the full scope from inspection through clearance testing. There is no separate charge for containment, HEPA vacuuming, or the final lab report. If we find additional growth once we open a wall, we stop and re-quote before continuing.

  • 01

    Full inspection and written scope

    A certified technician inspects the property with a thermal imaging camera, moisture meter, and boroscope. We document the affected areas with photos and give you a written scope with a flat price. Inspection takes 45 to 90 minutes depending on square footage.

  • 02

    Containment and negative air

    We build containment barriers with 6-mil plastic sheeting and zipper doors, then run a negative air machine with HEPA filters and an air scrubber. We verify negative pressure with a manometer before blasting starts and check it again at the end of each shift.

  • 03

    Dry ice blasting and HEPA vacuum

    Our technician blasts the affected framing in overlapping passes, then HEPA vacuums every surface inside the containment. We apply an antimicrobial solution and a borate treatment to bare wood, and install a vapor barrier in crawl spaces where soil moisture is a factor.

  • 04

    Post remediation clearance testing

    Three to seven days after blasting, we return for spore trap sampling and compare indoor counts to an outdoor baseline. You get the lab report in writing. If counts are above baseline, we re-treat the space at no additional cost.

Why homeowners choose dry ice blasting

Dry ice blasting mold removal in UNIVERSAL CITY solves a problem wet remediation cannot: it cleans the wood without adding water back into the structure. Here is what that means for your home.

Book an inspection

Tools and methods we use

Dry ice blasting machine

The core tool for every job. Feeds carbon dioxide pellets at roughly -109°F through a hose to freeze and lift mold off framing, concrete, and metal without water or grit.

Thermal imaging camera

Finds hidden moisture behind drywall and in ceiling cavities before we open anything up. Lets us scope the blasting work accurately instead of guessing at the extent of growth.

HEPA vacuum and air scrubber

Captures spores and debris inside the containment. The HEPA vacuum cleans surfaces after blasting, and the air scrubber runs continuously to keep airborne counts down.

Negative air machine with manometer

Maintains negative pressure inside the containment so spores cannot drift into living areas. We verify pressure with a manometer before blasting and at the end of each shift.

Local execution

Universal City sits in a warm, dry basin, but the housing stock tells a different story. The hillside homes around Universal City Plaza and the older multifamily buildings near the studios were built with attic and crawl space ventilation that was adequate for 1960 but not for today's tighter envelopes. Bathroom and kitchen exhaust fans vented into attics are one of the most common causes of growth we see. Roof leaks after winter rain are the other. When we run cryogenic mold removal UNIVERSAL CITY California jobs, we plan around two things: access and moisture source. Attic scuttles in these homes are often 24 by 30 inches, which limits how much equipment we can bring up at once. We stage the dry ice blasting machine outside and run hose through the scuttle. On the moisture side, we always identify and correct the source before blasting, because dry ice blasting for structural mold removal UNIVERSAL CITY only works if the wood stays dry afterward.

How dry ice blasting mold runs in Universal City

  • • Universal City Plaza
  • • Studio City
  • • Toluca Lake
  • • North Hollywood

Recent work

Attic mold cleanup in a Universal City hillside home [ A 1972 hillside home near Universal City Plaza had visible black mold across roughly 500 square feet of attic sheathing after a slow roof leak. The bathroom exhaust fan was venting directly into the attic, and relative humidity was holding at 68 percent. ]
Crawl space remediation in a Studio City duplex [ We blasted the joists and subfloor, HEPA vacuumed, installed a 6-mil vapor barrier over the soil, and ran a dehumidifier for 48 hours. Humidity dropped to 47 percent. Post remediation mold testing confirmed the air was clean in both units. ]
A powerful image of molten metal pouring in a heavy industry steel mill setting.
Response time
Response time

Same-day response for dry ice blasting mold in Universal City

When you call, a real person answers

Our phone line is staffed 24 hours a day, and a live dispatcher answers every call. For active leaks, sewage backups, and storm intrusion, we can have a technician on site within 60 to 90 minutes anywhere in Universal City and the surrounding San Fernando Valley. Our trucks carry containment plastic sheeting, zipper doors, HEPA filters, a negative air machine, an air scrubber, and a full dry ice blasting setup, so we can start work the same day we arrive. Most inspections are booked same day or next morning, and blasting jobs typically start within 48 to 72 hours of the written scope. If you need dry ice mold remediation in UNIVERSAL CITY on a weekend or holiday, we run crews seven days a week. Call (833) 929-5837 and we will get you on the schedule.

24/7
Live phone coverage

How our dry ice blasting process works

1

Phone intake

You describe what you are seeing: musty smell, dark staining on ceiling, mold in the HVAC system, or growth after a pipe leak. We ask about the age of the home and any recent water events. Within 15 minutes we schedule an inspection, usually the same day or next morning.

2

On-site inspection

A certified technician walks the property with a thermal imaging camera and a moisture meter to find hidden moisture. We use a boroscope inspection camera inside wall cavities and a spore trap sampler to confirm airborne counts. You get a written scope and a flat price before any work starts.

3

Containment setup

We build containment barriers with 6-mil plastic sheeting and zipper doors, then run a negative air machine with HEPA filters to keep spores from drifting into living areas. An air scrubber runs for the duration of the job. Setup takes about 45 minutes on a typical attic or crawl space.

What dry ice blasting mold costs

Typical 2026 pricing for dry ice blasting mold in Universal City runs $1,800 to $6,500 for residential scopes, with most single-area jobs landing between $2,200 and $3,800. That range covers containment, blasting, HEPA vacuuming, antimicrobial and borate treatment, and post remediation mold testing. Larger multifamily or commercial scopes with multiple contained zones run higher. We give you a flat price after the inspection, before any work begins, and we do not bill hourly.

01

Square footage of affected area

A 300 square foot crawl space takes far less blast time than a 1,200 square foot attic with multiple zones. We measure the affected area during the inspection and price the scope by square footage, not by the size of the whole house.

02

Access and containment complexity

Tight attic scuttles, finished ceilings, and occupied units add setup time. If we need to build containment around furniture or work in a tenant-occupied space, that adds labor. We flag these conditions during the inspection so the quote reflects them.

03

Extent of growth and substrate

Surface growth on framing blasts clean in one pass. Growth that has penetrated into porous sheathing or insulation may need a second pass or partial removal. We note the substrate condition during the inspection and price accordingly.

Frequently asked questions

How much does dry ice blasting mold removal cost in UNIVERSAL CITY California?

Most residential dry ice blasting mold jobs in Universal City run $1,800 to $6,500 in 2026, depending on square footage, access, and how far the growth has spread. A single attic or crawl space typically lands in the $2,200 to $3,800 range. Larger multifamily or commercial scopes with multiple contained zones can run higher. We give you a flat price after the inspection, before any work begins.

What is dry ice blasting mold remediation in UNIVERSAL CITY?

It is a dry cleaning method that uses compressed carbon dioxide pellets at about -109°F to freeze and lift mold off wood, concrete, and metal. The pellets sublimate on impact, so there is no water, no grit, and no chemical residue left behind. We contain the area, blast the affected surfaces, HEPA vacuum, and treat the wood with a borate solution afterward.

Is dry ice blasting safe for wood framing in UNIVERSAL CITY California?

Yes. Dry ice pellets are soft enough that they do not gouge dimensional lumber, engineered trusses, or older redwood framing. We adjust pressure and nozzle distance based on the substrate. On delicate sheathing we use lower pressure and slower passes. The process removes surface growth and staining without the abrasion damage you would get from sandblasting or soda blasting.

Does dry ice mold remediation require containment in UNIVERSAL CITY?

Yes, and we never skip it. Blasting aerosolizes spores, so we build containment barriers with 6-mil plastic sheeting and zipper doors, then run a negative air machine with HEPA filters to keep the work zone under negative pressure. An air scrubber runs the whole time. We verify pressure with a manometer before we start blasting and check it again at the end.

!

Get a flat price on Dry Ice Blasting Mold in UNIVERSAL CITY, California

We inspect, scope, and quote before any containment goes up. Call (833) 929-5837 and we will schedule a same-day or next-morning inspection for your Universal City property. IICRC-certified technicians, documented clearance testing, and a flat price you approve in advance.

Call Now: (833) 929-5837